Repair and Bonding Agents

Product Details:

• Bonding and Hardening agent based on modifiedplastic emulsion. Excellent bonding to concrete,plaster, and masonry works. Designed especially touse as a bonding agent and gauging liquid forcementatious system. Increases compressive andflexural strength as compared to reference mix.Reduces the permeability, hence makes mortarmore water light. Can be used as a water proofingcoat. Prevents leakage & dampness.

• 8-10 Kg. per 50 kg cement, for polymer modifiedmortar 4-5 kg.per 50kg cement.

• As a bonding agent for concrete and cementmortars.

• For structural repairs 8-10 Kg. per 50 kg cement andfor polymer modified mortar 4-5 kg.per 50kgcement. As a bonding agent apply directly 1:1 withcement 4-5m2/coat for bonding coat.Pack Size:1,5, 20 and 240 kg.

Additional Information:

• Delivery Time: 2 days

Product Details:

Description / Advantages:

• Two components epoxy Resin system which sets under water. Gives excellent compressive and tensile strength.

Application:

• As a bonding agent for concrete to concrete, steel to concrete and steel to steel under water leakages through structures like pipe line above and under water .can be used as a crack filling material internally & externally.

How to use:

• Mix base& reactor thoroughly and apply.

Additional Information:

• Production Capacity: Depends on application
• Delivery Time: 2 days

Product Details:

Description / Advantages:

Single component cementatious polymer. Used for modified filling and repairing cracks- both internal and external. Excellent adhesion and high strength mortar.

Application:

• Repairing of all types of cracks (internal & external). Give a thin plaster coat to even out surfaces.

How to use:

• mlx 3.5 to 4 volume s of powder to one part of water to get astiff consistency.

Product Details:

Description / Advantages:

An acrylic modified single component flexible coating in thixotropic consistency

Application:
Clean the joints, cracks, gaps from dust, oil, grease and loose particle, pre wet the crack with water for porous surfaces. Fill the joints, cracks, gaps by putty knife or spatula. Avoid formulation of bubbles or cavities while applying. After application leave the surface for at least one day. Apply second coal of BONDIT CRACK-SEAL if shrinkage is noticed. Allow it to dry for 1 to 3 hrs before painting work is taken up.

How to use:

• Mix thoroughly and apply by spatula putty (or) knife.

Product Details:

Description / Advantages:

Multipurpose rapid setting instant plugging mortar. Sets rapidly on contact with water. Hardens instantly under continuous wet conditions. can stop the leaking/dripping water, until the final repairs are carried out. Chloride free.

Application:

• Used in all areas where quick setting is required. All plugging works, quick repairs of concrete, screed, plaster, brick work. For stopping leakages in tunnels, cellars, pits, sewerage systems etc.

How to use:

• Mix 3 parts of Bondit plug 10s with 1part of clean water make dough and press with hand for 2 minutes in the place.

Product Details:

Description / Advantages:

Two component solvent free epoxy. Resin based bonding agent. Gives extended pot life. Develops high flexural and tensile strengths. Easily applied as a bonding agent for old to new concrete, Mix and use. Helps in repair and extension of structural concrete.

Application:

• used for bonding old concrete to new concrete.

How to use:

• Area should be free from dust, oil. Do not apply in wet condition. Mix base & hardener thoroughly until a uniform colour is obtained. Apply with brush to the prepared surface. New concrete should be placed within 3hours after applying Bondit Epoxy Bond when itis a still sticky.

Product Details:

Description / Advantages:

It is designed for application to minor imperfec- tions in concrete and masonry surfaces. It is suitable for application in the range of feather edge to 3mm and It is cost effective, time saving and high performance. Bondit repair mortar is designed for the repair and refurbishment of damaged concrete.

Application:

• Can be used for filling pinholes prior to over coating, general reprofilling over large areas, up to 3mm depth & fairing coat, in association with other mortars.

How to use:

• Clean the surface and remove any dust, plaster, oil, paint, grease, corrosion deposits. Roughen the surface to remove any laitance and expose the fine aggregate by light scrabbling. All the areas where Bondit repair mortar to be applied should be thoroughly soaked with clean water prior to the application of Bondit repair mortar
• Apply the mixed Bondit repair mortar to the prepared substrate, up to 3 mm thickness, by trowel. Apply with minimum working and let the mortar settle before final trowelling for smoothness. Do not execute when rainfall is expected unless the surface is protected.

Product Details:

Description / Advantages:

It is a liquid Membrane curing compound for concrete water based Wax Emulsion. Should be Single application by brush or spray on fresh concrete to prevent water loss. Eliminates curing where difficult to reach and where water Sacristy is there. Can be applied by brush also.

Application:

• Can be used for vertical concrete structures and columns, pavements, slip from structures like chimneys, cooling towers and silos, mass concrete faces, runways, CC roads and bridge decks canals etc.

How to use:

• Spray or brush application on freshly laid concrete.